Search results

After sitting for a week the faucet decided to work just fine without me needing to do anything.

Checked the aerator at the sink, it's clear. and actually broken since I broke it taking it off last year :) Filter at the pump is clear too.

At the end of last season, I blew out the water lines. Now my kitchen sink faucet has very low pressure but the sprayer has its usual good pressure. All the other faucets on the boat have great water pressure. This ever happen to anyone else?

I might be up for something in the RI, Block Island, or Vineyard areas.

Does anyone know the part number for the Asco Red Hat II solenoid that's used for the fresh water fill? I took a picture of it but it came out too blurry to read the part numbers. The solenoid stopped working on me so I had it replaced w/ a ball valve thinking it wouldn't be that big of a...

Anyone interested in some Raymarine electronics that came off of my 45 Yacht? - 2 e127 MFDs - VCM100 voltage control module - CP370 Digital Sonar - RMK-10 wired remote control - SR6 Raymarine SeaTalk HS network switch with Sirius Marine Weather - Raymarine keyboard (might be broken, not sure) -...

Anyone replace the cockpit fridge with something other than the overpriced uline unit? my unit is randomly deciding to stop cooling. I don?t care about the ice maker.

Has anyone replaced the gas struts that are supposed to hold the sunpad up? They appear to be part number ML33-80# from Ameritool. Does that mean they are part ML33 with an 80 pound capacity? I think I found them here but I want to double check to see if anyone else has done this...

sent you a PM

I saw a post on Facebook in the Formula Boats group that a couple of people have tried to join here and are waiting to be approved.

Thinking about having a Fisher cover made and I?m curious about people?s experience with them. Specifically: 1) how many years do have you had it and how is it holding up? 2) how does the imron hold up? Any scratching, scuffing, etc.?

Stupid me figured this out last year, but didn?t write it down. How much oil does the generator take for an oil change (with filter)? The manual says 4.3 US Gallons or 4.0 liters. Obviously one of those is wrong. (2011 45? Yacht)

apparently this is the only one I have right now. I'll take some more tomorrow when I'm back at the boat. PM me your email or cell and I'll send them to you.

Anyone ever have a situation where their engine solenoids wouldn?t shut off? My parallel solenoid won?t energize or deenergize either. As I watch the colt meter when I start the engines it seems like the parallel is on, but the light on the switch isn?t. 2011 45 Yacht

We were away for about a week and spent some time on a mooring and some time at a dock. About half the time the fridge was on 12v and the other half was on 120v. Everything worked great. Left the boat for a couple of days and went back today and the fridge wasn?t cooling in either 12v or 120v...

For the life of me I can?t find where the anodes are on the Charge Air Cooler of a Volvo D6-435 engine. Does anyone have a picture of where they are? (The picture in the manual doesn?t show it on an assembled engine) I have a 2011 45? Yacht, but the location should be the same on any D6...

What does everyone use for anti-fouling paint on their pods and swim platform arms?

What zincs are you guys using for your hull and swim platform? Looking at the measurements of my zincs and comparing it to zincs on boatzincs.com, I think the hull zincs are the ZC-406 model (https://www.boatzincs.com/zc-406.html) and the swim platform lift arms are the 2-13/16 R-2 rudder zincs...

What do you guys think should I leave the seacocks opened or closed? I opened them to drain them, but then closed them thinking that would prevent bugs and other critters from crawling in. what say you?

I?ve got a couple of spots that the clearcoat is chipping and flaking off. Seems to be mostly on the red accent stripes. Anyone have any suggestions on how to deal with it? Should I wet sand the spots then touch it up with more clearcoat?