Search results

I currently have a Formula 232LS. I'm thinking on moving up to a 260SS. I want to stay with a single, but attracted to the extra room. What is the (opinion) of the best engine to get it with. That came stock from Formula. I boat mainly on a river. Calm most of the time. I currently have a big...

I was looking at this boat. I currently have a 232LS. I would be increasing size of boat, cockpit, cabin, etc...I'm seeing most with 6.2 motors. I'm wondering if this is under powered?? I have a 502 in my boat. Formulas are heavy!!! I'm not looking to go to twins. Just don't know anyone with...

I currently have a Formula232LS. I'm looking at buying a 260SS. I'm looking to go bigger, but don't want twins. I know it will be slower than what I have, but maybe not as slow as a PC? I don't know. Does anyone know what the engine sizes that were offered by Formula? Does anyone have any...

I wonder why Formula didn't put air vents in my boat. I have a 1997 232 ls. I never overheated but I see so many boats with them.:confused:

Does anyone have experience with the Hardin Marine side mount control? It replaces the Merc. one control lever with two control levers. Thanks

Has anyone used any supports for the windshield. I have a 232ls and going over the windshield to the front deck is a little sketchy. I feel a support for the windshield would be nice.

I'm in the process of changing all my switch covers. I have a 1997 232ls. I have one switch cover soo worn that I can't read what it is for. When I use the switch, I can't tell what it's for. The 232ls/232BR & 252ls/252BR is all the same. it's on the right side of the wheel, second row down...

I would like to change my rocker switch covers. All the switches work, but some look old or faded. Is it hard to just change the covers? Is it hard to change the lights in them? Does anyone know what company "Formula" uses for the rocker switches? Thanks!

Does anyone have any Dash Panels from a late 90's 232,252, or252BR? I would be willing to rent/buy. I need them for a Template for new ones to be made. Thanks!!!

What are the advantages/disadvantages on installing them? Thanks guy's!

Does anyone know of a company/company's that do "drop down bolsters" other than Mcleod? I have been searching, with no luck. Thanks.

I'm looking to add a trim "position" indicator to my already installed Bennett Trim Tabs. I am looking at an indicator tpi 2000? It is a starboard and port all in one. Any advise? Thanks...

Does anyone have this issue? I go too fast when I switch into gear at lower speed. I have a 350 mag & B3 with 3x3 props. My idle rpms 700-800. I want to be able to go slower when in the marina. I have no top end issue that I know of. Thanks.

Is there anyway to go to threads that I replied to? I don't always remember everyone I may have commented in. Thanks

I'm looking to replace my lost fuel cap on a 1997 232ls. It was the one with the plastic around the cap with the "Bird" on it. I'm told that it may be from Perko? I think it's a 2" not 1 1/2". I don't care if it is Formula one just need it to fit. At the gas dock filling, super big waves, the...

Does anyone have any experience removing the steering wheel and what it is attached too on a 232 ls. I tried to remove the wheel and being a "saltwater" boat, I was only able to get out three of the six bolts. The remaining tree, one sheered off at the head, two have the tips of "easy out" tools...

Does anyone have any info regarding a "Lowrance elite 5m" gps? I am looking for a GPS only unit, not w/fishfinder. I am not looking to spend more than $500. I also have limited dash space. For a 232ls. Thanks guys.

I have a 1997 232 LS. It currently has pedestal seats that flip up. I'm thinking on going to full stand up bolsters. I don't know what company sells them. I'm also worried that they may be too tall. Can you order them in different heights? Has anyone done this? Any regrets? Thanks

Has anyone drilled the plexi cabin door? I have a 232ls and want to put a handle on it (for opening & closing). I was told to drill slowly? Graduate in size to desired size? I never drilled plexi glass. Don't know if these recommendations are true or not. Thanks.

I have a 232LS. It has a 350 Mag EFI w/ brave3. It weighs about 4200lbs. dry. My speedo does not work right now. What do you guys guess would be my speed ( roughly ) at 4000 rpm's, calm water, alone in boat w/ minimum equip? I was running between 4000 and 4500 rpm's. Thanks... P.S. still had...