Recent content by Jmwarren

Hello All, Short Version - Does anyone have measurements for the Aft Berth on a 41PC? Long Version Well our 34PC is SOLD! We're looking at moving up. We'd love a 45 or 48 but at this point they are just too much money. We've located a 41pc thats quite a distance away, before going out to...

Hi Guys, I pulled my Stern Tow Eyes at the end of the season due to a small leak. The core is dry and I'll be carving some out and filling with epoxy before re-installing the eyes in the spring. This got me thinking, if the tow eye sealant was starting to fail, the trim tabs can't be far...

Has anyone tackled this? I'm looking at mounting a flatscreen in the new factory location, on the bulkhead over the aft cabin. I realize it wont be viewable with the privacy curtian closed, but that shouldn't be an issue. If anyone has a newer 34PC and wants to snap some photos from the glovebox...

Hello All, I'll be replacing the transducer from the Factory ST60 Depth with one for my new Raymarine E7D. Does anyone know what the rise of the hull is in the factory location? (Mine is accessible under the aft cabin rear storage/seat) Thanks

Hi Guys, I'm sure the sealants on my 04 34 PC have seen better days. I'm thinking about rebedding all the hardware in the spring. Has anyone done this on this year/model? How hard is it to reach the backing plates to the bowrail? I get the feeling I'll have to pull apart the whole interior! Thanks

Hi Guys, I'm looking at adding an RV style water filter to my 04 34pc My plan was to add a male hose fitting just after the water inlet and a female hose fitting on the primary water line. The filter will just slide in place. If the filter gets clogged and I dont have a spare its as simple as...

Hi Guys, I was wiring in some new hardware this weekend and wanted to test it before hardwiring it. The boat is 100% stock prior to this work. I pulled the 12v socket next to the helm to use it as a temp. 12v source to test the hardware. I popped the break to kill the power so I could wire...

Hi Guys, I'm putting some platform cleats as well as davits on and am wondering if the platform is cored? If it is I plan to crave the coring out around the holes and epoxy them so that there is no chance for water incursion. If not I'll just use some 4000uv to seal them. Thanks

Hi Guys, We're looking to buy a memory foam matress pad for the aft to improve comfort for guest. The boat is over 2 hours away. If anyone can give me a length and width when the cabin is configured as a birth it would be appreciated! Thanks,

Hi Guys, I've been trying to find this thing since I know it needs to be oiled. I've tried under the dash by pulling the glove box forward. Under the access hatch beneath the wet bar. Behind or around the Starboard lounger. I've had zero luck locating the damn thing! Formula is stumped and...

Hi Guys, I'm in the process of upgrading from my Navman Tracker 5500 to a new ray marine unit. First question is whats the best way to enlarge openings on these panels. They seem to be made of painted aluminum? Thanks!

Hi Guys, In my last inspection of the bilge I notice a small amount of rust around the manifold/riser connection. All three others were perfectly clean. I'd like to pull this riser to replace the gasket and double check that the manifold is OK (it's a late 04, launched first in 05 and fresh...

Hi Guys, I'm looking at installing a Magma "Newport" Grill (unless anyone else has suggestions). I'm lost as to which mount to use and where to install it. I'm sure some of the guys that have the same or similar boats must have some suggestions and photos of your setups? Thanks!

Anyone have any idea how tall a fender will fit? I just bought some 10"x26" that look like they may be too big. I know they wont fit in the fender hoolders, but I plan to remove and replace them. I'm just worried they won't fit height wise! Anyone running a fender this large and storing them...

Does anyone know where they usually stick these things? Thanks